Dolmar owners manual

Brand: Sachs Dolmar. UPC: Does not apply. Download sachs dolmar manual for FREE. Browse our daily deals for even more savings! Free delivery and free returns on eBay Plus items! Save sachs dolmar to get e-mail alerts and updates on your eBay Feed.

Unfollow sachs dolmar to stop getting updates on your eBay feed. You'll receive email and Feed alerts when new items arrive. Switch on STOP, fault or short-circuit in the wiring, plug cap or spark plug defective. Choke in wrong position, carburetor defective, fuel filter dirty, fuel line bent or interrupted, torn, Perforated.

Cylinder base packing ring defective, radial shaft packings defective, cylinder or piston rings defective. Spark plug does not seal. Spring in starter broken, broken parts inside the engine. Wrong carburetor adjustment, flooded by usage of the ckoke. Engine starts, but dies immediately. Wrong idling adjustment, fuel filter or carburetor dirty. Tank venting defective, fuel line interrupted, cable defective, STOP switch defective. Decompression valve dirty. Air filter dirty, wrong carburetor adjustment, muffler clogged, exhaust channel in cylinder clogged, spark arrester screen clogged, worn piston.

Disengage the choke lever pull out and turn clockwise. Before you start the engine, make sure that the saw chain is not contacting anything. Carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and the muffler away from your body. Do not operate a chain saw that is damaged, is improperly adjusted, or is not completely and securely assembled. Be sure that the saw chain stops moving when the throttle control trigger is released.

Shut off the engine before setting it down. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.

When cutting a limb that is under tension be alert for springback so that you will not be struck when the tension on the wood fibers is released. Keep the handles dry, clean, and free of oil or fuel mixture. Operate the chain saw only in well-ventilated areas. Do not operate a chain saw in a tree unless you have been specifically trained to do so.

For example, if improper tools are used to remove the flywheel or if an improper tool is used to hold the flywheel in order to remove the clutch structural damage to the flywheel could occur and could subsequently cause the flywheel to burst. When transporting your chain saw, use the chain protection cover.

Low kickback bars and low kickback chains are designed to reduce the risk of kickback injury. The use of any chain saw may be hazardous. It is important that you read; fully understand and observe the following safety precautions and warnings. Reactive forces, including kickback, can be dangerous. Careless or improper use of any chain saw may cause serious or fatal injury. Observe all applicable local safety regulations, standards and ordinances. Minors should never be allowed to use a chain saw.

Bystanders, especially children and animals should not be allowed in the area where a chain saw is in use fig. Store it in a locked place away from children. Be sure that anyone using your saw understands the information given. You must be in good physical condition and mental health and not under the influence of any substance drugs, alcohol , which might impair vision, dexterity or judgment. All DOLMAR saws are therefore provided with an antivibration system which is essential for those using chain saws on a regular or sustained basis.

Antivibration systems do not guarantee that you will not sustain Whitefinger disesase, however, they reduce this danger considerably. Nevertheless, continual and regular users should observe their hands and fingers and in case of any abnormal symptoms, seek medical advice immediately. Clothing must be sturdy and snug-fitting, but allow complete freedom of movement. Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, or anything that could become entangled with the saw or brush.

Wear overalls or jeans with a reinforced cutting resistant insert fig. Protect your hands with gloves when handling saw and saw chain. Heavy-duty, nonslip gloves improve your grip and protect your hands. Proper eye protection is a must. Non-fogging, vented goggles and a face screen is recommended.

Their use reduces the risk of eye and facial injury. Wear an approved safety hard hat to protect your head. Chain saw noise may damage your hearing. Always wear noise protection equipment ear plugs or ear muffs to protect your hearing. Never modify a chain saw in any way. Bow guide bars substantially increase the potential for kickback and severe or fatal injury due to the greater kickback zone of the bow design. Always stop the engine before putting a chain saw down or carrying it.

Carrying a chain saw with the engine running is extremely dangerous. Accidental acceleration of the engine can cause the chain to rotate. By hand: When carrying your saw by hand, the engine must be stopped and the saw must be in the proper position. The chain protection cover should be over the chain and the guide bar must point backwards. When carrying your saw the bar should be behind you fig. By vehicle: When transporting in a vehicle, keep chain and bar covered with the chain guard.

Properly secure your saw to prevent turnover, fuel spillage and damage to the saw. Make sure the saw is not exposed to heat or sparks. For assembly follow the procedure in the appropriate section "Mounting Guide Bar and Chain" of this manual. DOLMAR chain, guide bar and sprocket must match each other see the appropriate section in this manual. Proper tension of the chain is extremely important. In order to avoid false setting the tensioning procedure must be followed as described in this manual.

Always make sure the hexagonal nut s for the sprocket guard is are tightened securely after tensioning the chain. Check chain tension once more after having tightened the nuts and thereafter at regular intervals always before starting to work. If the chain becomes loose while cutting, shut off the engine and then tighten.

Never try to tighten the chain while the engine is running! Gasoline is an extremely flammable fuel. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any sparks or flame near the fuel fig. Fuel your chain saw in well ventilated areas or outdoors. Always shut off the engine and allow it to cool before refueling. Select bare ground for fueling and move the chain saw at least 10 feet 3 m from fueling spot before starting the engine fig. Check for fuel leakage while refueling and during operation.

If fuel or oil leakage is found, do not start or run the engine until leak is fixed and spilled fuel has been wiped away. Clothing with fuel on it has to be changed immediately this is a danger to your life! Avoid skin contact with fuel. Never loosen or remove the cap of the fuel tank while the engine is running. Do not drop start. This method is very dangerous because you may lose control of the saw fig. Place the chain saw on firm ground or other solid surface in an open area.

Maintain a good balance and secure footing. Place your right foot through the rear handle opening and firmly grasp the front handle with your left hand fig. Be absolutely sure that guide bar and chain are clear of you or all other obstructions and objects, including the ground, because when the engine starts in semithrottle position, engine speed will be fast enough for the clutch to engage the sprocket and turn the chain which may cause a kickback. Do not allow the grip to snap back, but guide the starter rope slowly back to permit the rope to rewind properly.

Failure to follow this procedure may result in injury to hand or fingers and may damage the starter mechanism. At correct idle speed, chain should not turn. For directions to adjust idle speed, see the appropriate section of this instruction manual. Do not use a saw with incorrect idle speed adjustment. Adjust the idle speed yourself according to the appropriate section of this manual. Check the saw chain tension frequently, especially just after installing a new chain.

New chains may stretch more during their initial use. A properly adjusted saw chain can be pulled freely around the guide bar by hand without sagging. Always stop the engine and wear gloves when checking or adjusting the chain tension. Operate your chain saw only outdoors. Operate the saw under good visibility and daylight conditions only.

Take extreme care in wet and freezing weather rain, snow, ice. Put off the work when the weather is windy, stormy or rainfall is heavy. Clear the area where you are working.

Avoid stumbling on obstacles such as stumps, roots or rocks and watch out for holes or ditches. Be extremely cautious when working on slopes or uneven ground. There is increased danger of slipping on freshly debarked logs. Always hold the saw firmly with both hands when the engine is running. Place your left hand on the tubular handle and your right hand on grip and throttle lever. Left-handers should follow these instructions too.

Wrap your fingers tightly around the handles, keeping the handles cradled between your thumb and forefinger fig. With your hands in this position, you can best oppose and absorb the push, pull and kickback forces of your saw without having it slip out of your grip see section of reactive forces.

Make sure your chain saw handle and grip are in good condition and free of moisture, pitch, oil or grease. Always start a cut with the chain running at full speed and the spike bar in contact with the wood. Never use the saw with one hand. You cannot control reactive forces see pages 10 to 12 and may lose control of the saw. Do not operate your chain saw in semi-throttle position.

Cutting in this position does not permit the operator proper control of the saw or chain speed. Use your chain saw for cutting only.

It is not designed for prying or shoveling away limbs, roots or other objects. When sawing, make sure that the saw chain does not touch any foreign materials such as rocks, nails and the like fig. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive. If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

Would you like to receive an email when new answers and questions are posted? Please enter your email address. Sachs Dolmar Manual. Get this manual by email. Need help?